FAQ & Information

Chrome, Titanium Gold and Stainless Steel – X-CLEAN and a soft fibre cloth (neat vodka works too).

Brass – A clean and dry microfibre cloth.

Powder Coat – Carefully remove any loose deposits with a wet sponge and use a soft fibre cloth, with a little mild household detergent, then rinse with clean water.

Silicone – A clean cloth and soapy water (unscented hand or dishwasher soap works well).

SPORT (NS) upper plate = 230mm

SPORT (NS) base plate = 230mm

XPERT (NX) upper dome = 380mm

XPERT (NX) microbase = 120mm

XPERT Pro (PX) upper dome = 280mm

XPERT Pro (PX) base = 120mm

No, we advise against this and instead recommend the Ball Mount for studio use

A maximum of two people can use a X-STAGE/X-STAGE Lite pole at one time

A maximum of two people can use a XPERT Pro pole at one time

A maximum of two people can use a XPERT pole at one time

A maximum of two people can use a SPORT pole at one time

Yes, please check in our shop section

Yes, please check in our shop section

Competition/dual lined multi-piece’s are designed for commercial (studios and gym) usage. They have an inner steel core that adds rigidity and strength at taller heights. They use a 2.5m A pole and a single X-JOINT and dual lined extension to reach your desired height.

We suggest removing any jewellery, watches and piercings before doing pole or aerial activities.

All required hex keys are supplied with your pole set. Additionally, you will need a tape measure and a spirit level.

No, the silicone sheath is glued to the pole.

You may have tightened the spinning and static screws on the round section of the base instead of the flat section. We do offer a repair service for this fault. Please contact our technical team for advice on either [email protected] or 00 44 (0)208 449 4400 and select option 3.

Yes, if you should need a replacement screw(s) for any X-POLE product, please contact our technical team on 0044 (0)208 449 4400 or at [email protected] for advice.

X-STAGE/X-STAGE Lite (NST03/NST03LT)

A-pole retaining screws – 3 x M8 x 8
Static/Spinning – 2 x M10 x10
Bearing locking screws –  3 x M10 x 8 (Domed)
(NST02 – 3 x M10 x 8 Flat)
Bearing locating 1 x M6 x 5

XPERT (NX)

Adjuster locking screws – 3 x M10 x 8
Static/Spinning – 2 x M10 x 10

XPERT Pro (PX)

Adjuster locking screws – 3 x M10 x 8

Pre-2014 XPERT (XX)

Adjuster locking screws – 3 x M8 x 8
Static/Spinning – 2 x M8 x 10

Please purchase a replacement item from our shop section

Ensure that the X-JOINT is fully contracted and then insert a broom handle or similar item in to the pole to dislodge the X-JOINT.

You may have tightened your adjuster screws onto the adjuster rod thread, causing damage to the thread in the process.

If your pole is up to 12 months old, we do offer a free repair service for this fault. Please contact our technical team for advice on either [email protected] or 00 44 (0)208 449 4400 and select option 3.

If your pole is older than 12 months, we suggest purchasing either replacement parts or a a new pole to remedy this issue. Please contact our technical team for advice on either [email protected] or 00 44 (0)208 449 4400 and select option 3.

Yes, there is no limit or pre-requisite for pole fitness. Pole exercise is extremely physical and uses muscles that you will not have used before and therefore if you are not warmed up; muscle damage, strains and injury can occur. Before using a pole it is mandatory to warm up and, after use, cool down. It is highly recommended that before you use your pole you purchase a suitable DVD to learn the basic moves or attend pole fitness classes. Never try moves beyond your ability without an instructor. If at any time whilst using your pole you feel uncomfortable, your muscles hurt, or you are short of breath – take a break. Always rest between moves & exercise sensibly, if you experience any health issues, seek medical advice. But if you have any concerns, please contact your doctor.

1 x Main Frame Carry Case, 1 x Main Stage Frame, 1 x 4mm, 5mm and 6mm Hex Key, Side Skirts (X-STAGE only), Fixed Wheels (x2), 1 x Pole Case, 1 x X-STAGE A pole,1 x X-STAGE B pole, 1 x Bearing unit, 1 x 250mm X-JOINT, Instruction manual, 6 x stage floor plates and 2 x stage floor plates carry cases.

1 x XPERT Pro A pole, 1x XPERT Pro B pole, 1 x 250mm extension, 1 x Top Insert, 1x 125mm extension, 2 x 200mm X-JOINT (3 x 200mm X-JOINT’s in a 40mm pole set), 1 x 180mm X-JOINT, base, upper dome, instruction manual and a 6mm Hex key.

1 x XPERT A pole, 1x XPERT B pole, 1 x 250mm extension, 1 x Top Insert, 1x 125mm extension, 2 x 200mm X-JOINT (3 x 200mm X-JOINT’s in a 40mm pole set), 1 x 180mm X-JOINT, base, upper dome, instruction manual, 5mm Hex Key and 6mm Hex key.

1 x SPORT A pole, 1x SPORT B pole, 1 x 250mm extension, 1x 125mm extension, foam padding, 2 x 200mm X-JOINT (3 x 200mm X-JOINT’s in a 40mm pole set),1 x 180mm X-JOINT, articulating base, upper plate, instruction manual, Tightening/Releasing Tool, 6mm Hex key and a carry/storage case.

You can purchase additional extensions and X-JOINT’s for your second hand pole from our shop area and you can download PDF files of the approprate manual from our support section. If you require additional screws to replace lost ones, please contact our technical team for advice on either [email protected] or 00 44 (0)208 449 4400 and select option 3.

Depending on amount of use and maintenance, your pole can last from 2-5 years.

No, the X-STAGE pole set requires the X-STAGE base and bearing carrier to function.

No, SPORT, XPERT and XPERT Pro poles are not compatible with the X-STAGE bearing unit.

Use the image below to identify which generations/version X-STAGE you have:

Pre-2014 X-JOINT’s have a circular keyway pin in the centre of the joint. Post-2014 X-JOINT’s have an oval/pill shaped keyway pin at the centre of the X-JOINT.

Post 2014 X-JOINT

Pre-2014 X-JOINT

You will need to measure from the floor to the ceiling in the place where you intend to use the pole and then review the appropriate height chart for the pole to ascertain what extension you will need to reach your desired height. This video shows you how to measure your floor to ceiling height:

No ladder is required to set up any of our pressure mounted poles (SPORT, XPERT and XPERT Pro) or our freestanding poles (X-STAGE and X-STAGE Lite).

No, this is not possible.

No, this is not possible.

Please check the shape of the slot inside the A pole. If it is a semi-circle, it is a pre-2014 XPERT. If it is half an oval, it is a post-2014 XPERT.

Please check the shape of the slot inside the A pole. If it is a semi-circle, it is a pre-2014 SPORT. If it half an oval, it is a post-2014 SPORT.

X-JOINT’s are supplied inside the extensions of your set.

X-POLE sets are supplied with 2 x 200mm and 1 x 180mm X-JOINT’s as standard. Additional X-JOINT’s can be purchased from your local X-POLE office.

While the X-STAGE pole can not be made taller, it can be made shorter by using an NE extension.

To work out which extension you will require, follow this formula:

Your floor-to-ceiling height in millimetres – 1500mm – 135mm and then round down to the nearest extension (500mm, 750mm or 1000mm).

e.g. 2500mm – 1500mm – 135mm = 875mm (round down to 750mm)

X-STAGE height chart

Please contact our sales team for advice on either [email protected] or 00 44 (0)208 449 4400 and select option 1.

Unfortunately, we no longer manufacture parts for these products.

Yes. You will need to purchase an adapter X-JOINT which will allow you to use NE extensions on your old pole.

Home Mounts are supplied with 4 x 5 x 40mm. Ball mounts do not come with screws.

This will depend on what type of mount you are using and the material you are attaching your mount to. Please contact our technical team for advice on either [email protected] or 00 44 (0)208 449 4400 and select option 3.

Please speak to our technical team regarding weight limits or visit this page.

The X-POLE X-FLY flying pole weighs approximately 18kg

The X-POLE LyraPole weighs approximately 15kg

The X-POLE X-STAGE weighs 100kg. The X-STAGE Lite weighs 75kg.

The X-POLE XPERT Pro weighs 21kg

The X-POLE XPERT weighs 21kg

The X-POLE SPORT weighs 18.5kg

Our boxing differs depending on the product, here is a list of the different box sizes:

A-FRAME: L – 1600mm H – 290mm D – 290mm
SPORT: L – 1180mm H – 270mm – D – 80mm
XPERT: L – 1180mm – H – 460mm – D 125mm
XPERT PRO: L – 1170mm H – 430mm D – 140mm
X-STAGE: L – 950mm H – 410mm D – 250mm
X-STAGE LITE: L – 1015mm H – 315mm D – 205mm
X-STAGE PLATES: L – 750mm H – 120mm – D – 830mm

X-POLE pressure mounted poles can be installed in rooms with solid ceilings, or ceilings that have a joist or girder above them. Pressure mounted poles use pressure between the floor and ceiling to keep them stable. There is a possibility that damage could be caused to the ceiling.

Chrome – The industry standard finish and a good all-rounder for all levels of skill/experience. High grade steel poles are coated in Chrome and polished to a high finish.

Stainless Steel – A great alternative to Chrome or Brass and very hard wearing. Stainless Steel poles are polished to a mirror finish. Also good for polers with nickel allergies and ideal for commercial environments (studios and gyms) with a lot of polers!

Brass – Great in hotter climates as the grip factor increases with the ambient temperature and the perfect choice for polers with nickel allergies.

Titanium Gold – Chrome poles are taken and electronically coated with the finish for an enhanced grip.

Powder Coat (Black, Pink & White) – Useful for people who struggle to grip standard metal poles. Very high grip factor! Steel poles are powder coated and baked to seal the finish. Available in black, white and hot pink!

Silicone (Black & Pink) – The ultimate easy grip pole! Minimal skin to pole contact needed. Steel poles have a silicone sleeve attached to the surface of the pole. Available in 45mm pole diameter only.

Chrome – 40mm and 45mm – Steel core with Chrome coating applied

Stainless Steel – 40mm and 45mm – Highly polished Stainless Steel pole

Brass – 40mm and 45mm –Brass tube.

Titanium Gold – 40mm and 45mm – Steel core with Chrome coating that is then electronically treated to give the Gold finish with additional grip

Powder Coat (Black, White and Pink) – 40mm and 45mm – Steel core with a powder coat layer baked on

Silicone (Black and Pink) – 45mm – Steel core with a 5mm thick silicone sheath glued to the pole